The Deterministic Networking (DetNet) Working Group focuses on deterministic data paths that operate over Layer 2 bridged and Layer 3 routed segments, where such paths can provide bounds on latency, loss, and packet delay variation (jitter), and high reliability. The Working Group addresses Layer 3 aspects in support of applications requiring deterministic networking. The Working Group collaborates with IEEE802.1 Time Sensitive Networking (TSN), which is responsible for Layer 2 operations, to define a common architecture for both Layer 2 and Layer 3. Example applications for deterministic networks include professional and home audio/video, multimedia in transportation, engine control systems, and other general industrial and vehicular applications being consider by the IEEE 802.1 TSN Task Group. The Working Group will initially focus on solutions for networks that are under a single administrative control or within a closed group of administrative control; these include not only campus-wide networks but also can include private WANs. The DetNet WG will not spend energy on solutions for large groups of domains such as the Internet. The Working Group will specify an overall architecture that encompasses the data plane, OAM (Operations, Administration, and Maintenance), time synchronization, management, control, and security aspects which are required to enable a multi-hop path, and forwarding along the path, with the deterministic properties of controlled latency, low packet loss, low packet delay variation, and high reliability. The work applies to point-to-point (unicast) and point-to-multipoint (multicast) flows which can be characterized in a manner that allows the network to 1) reserve the appropriate resources for the flows in advance, and 2) release/reuse the resources when they are no longer required. The work covers the characterization of flows, the encapsulation of frames, the required forwarding behaviors, as well as the state that may need to be established in intermediate nodes. Candidate Layer 3 data plane technologies that may be used, without modification, include: IP and MPLS. The working group will document which deployment environments and types of topologies are within (or outside) the scope of the DetNet architecture. This work focuses on the data plane aspects and is independent from any path setup protocol or mechanism. The data plane will be compatible with the work done in IEEE802.1 TSN. The Working Group's scope explicitly excludes modifications of transport protocols, OAM, Layer 3 forwarding, encapsulations, and control plane protocols. DetNet is chartered to work in the following areas: Overall architecture: This work encompasses the data plane, OAM, time synchronization, management, control, and security aspects. Data plane: This work will document how to use IP and/or MPLS to support a data plane method of flow identification and packet forwarding over Layer 3. Data flow information model: This work will identify the information needed for flow establishment and control and be used by a reservation protocol or by YANG data models. The work will be independent from the protocol(s) used to control the flows (e.g. YANG+NETCONF/RESTCONF, PCEP or GMPLS). Identification of additional YANG models: This work will document device and link capabilities (feature support) and resources (e.g. buffers, bandwidth) for use in device configuration and status reporting. Such information may also be used when advertising the deterministic network elements to a control plane. Control plane related information will be independent from the protocol(s) which may be used to advertise this information (e.g. IS-IS or GMPLS extensions). Any new YANG models will be coordinated with the Working Groups that define any augmented base models. As needed, problem statement: This effort will establish the deployment environment and deterministic network requirements. As needed, vertical requirements: This effort will detail the requirements for deterministic networks in various industries, for example, professional audio, electrical utilities, building automation systems, wireless for industrial applications. To investigate whether existing data plane encryption mechanisms can be applied, possibly opportunistically, to improve security and privacy. The WG coordinates with other relevant IETF Working Groups, including CCAMP, PCE, PALS, TEAS, OSPF, IS-IS, TSVWG, and 6TisSCH. As the work progresses, requirements may be provided to the responsible Working Group, e.g. PCE, TEAS, and CCAMP, with DetNet acting as a focal point to maintain the consistency of the overall architecture. The WG will liaise with appropriate groups in IEEE and other Standards Development Organizations (SDOs). WG deliverables include: As standard track or informational RFCs Overall architecture Data plane specification Data flow information model YANG model augmentations WG sustaining/informational documents may include: These documents may not necessarily be published, but may be maintained in a draft form or on a collaborative Working Group wiki to support the efforts of the Working Group and help new comers: Problem statement and (constrained) deployment environments User-driven use cases